through quenching

It was shown that herbicide had a strong ability to quench the CAT fluorescence mainly through a static quenching procedure.

结果表明，除草剂对过氧化氢酶的荧光有较强的猝灭作用，且静态猝灭是引起荧光猝灭的主要原因。

The appearance of the medium-frequency through quenching and the corresponding quenching machine has a great significance to improve the technology of heat treatment in china.

中频穿透淬火工艺及相应的淬火机床的问世，对改善和提高我国的热处理工艺和设备水平有一定意义。

The kinetic high-temperature reaction process in the combustion front was analyzed through quenching of combustion front.

结合燃烧前沿激冷淬熄法，分析了其燃烧前沿高温动态反应过程。

The experimental results show that the fluorescence quenching of BSA by theophylline is due to the formation of theophylline-BSA complex through both static quenching and nonradiative energy transfer.

实验结果表明，茶碱与BSA形成基态复合物导致BSA内源荧光猝灭，猝灭机理主要为静态猝灭和非辐射能量转移。

Through rapid heating and quenching the grain size of LM_2 steel may be fined down to 4.2 μ m, and its mean intercept length of carbide particles is < 0.32 μ m.

LM2钢经1050℃快速加热淬火后，基体晶粒尺寸可细化至4.2μm以下，碳化物平均截线长小于0.32μm。

Results of the present study revealed that low light conditions and low temperature changed the chlorophyll fluorescence characteristics of cotton leaves, in order to dissipate energy mainly through non-photochemical quenching.

研究结果认为，低温弱光改变了棉花叶片的叶绿素荧光特性，棉花叶片在低温和弱光条件下主要通过非光化学猝灭来耗散能量。

The mechanism of Cu(ⅱ) and Fe(ⅲ) binding to human serum albumin has been studied through the quenching of the intrinsic fluorescence of HSA.

通过研究Cu（Ⅱ），Fe（Ⅲ）对人血清白蛋白（HSA）内源荧光的猝灭，探讨了Cu（Ⅱ），Fe（Ⅲ）与人血清白蛋白的结合机理。

It is indicated that quenching tempering microstructure has been fined and controlled in the range of specification through quenching process adjustment.

对淬火工艺经过调整后，淬回火组织明显细化，并能控制在技术要求范围。

Energy saving and environmental protection can be achieved simultaneously through the coke dry quenching technology ( CDQ) that employs the recirculating inertial gas to cool off the coke.

干熄焦工艺具有节能和环保双重效益，其基本原理是利用循环惰性气体冷却焦炭。

The results show that the best quenching temperature is850 ℃, the hardness is not significantly changed ( 50~ 53 HRC) through different quenching and tempering temperature.

结果表明，试验钢的最佳淬火温度为850℃，试验钢经不同温度淬火、低温回火后，钢的硬度变化并不显著，在50~53HRC之间；

The hardness of 45 steel through surface quenching with plasma reaches about 800 HV. Thus, the method of heat treatment using plasma as heat source is practical.

45号钢经等离子体表面淬火后，硬度在800HV左右，表明采用等离子体热源对工件进行热处理是可行的。

Main controller adopted RS232 to communicate with robot controller through I/ O regulate plasma quenching welder.

主控机通过I/O控制等离子焊机，采用RS232与机器人控制器通讯。